Person:
Wong, C. P.

Permanent Link
https://hdl.handle.net/1853/71846
Associated Organization(s)
ORCID
ArchiveSpace Name Record

Filters

2002 - 2003 4
4
4
4
4
Reset filters

Settings
Author: Fan, Lianhua × Author: Wong, C. P. × search.filters.applied.f.isOrgUnitOfPublicationTitle: College of Engineering ×

Publication Search Results

Now showing 1 - 4 of 4
  • Thumbnail Image
    Item
    Adhesion Evaluation on Low-Cost Alternatives to Thermosetting Epoxy Encapsulants
    (Georgia Institute of Technology, 2003-04) Wong, C. P. ; Fan, Lianhua
    The thermosetting epoxy curing systems have been widely used as encapsulants in the electronic packaging industry. With the continual evolving of electronic product markets, material suppliers have been challenged to provide more options to meet the requirements of advanced, yet cost effective, packaging solutions. In this paper, two low-cost alternative materials have been investigated experimentally regarding their adhesion and reliability performance, and these have then been compared with the thermosetting epoxy systems. One of the materials is thermoplastic bisphenol A epoxy/phenoxy resin, and the other is an interpenetrating polymer network composed of an epoxy curing component and a free radical polymerizable component. Some formulations of the materials being studied could exhibit excellent adhesion, durability and application reliability. While reworkability is expected for these materials, they are promising as cost effective encapsulants for electronic packaging, and may be applied with appropriate processing techniques.
  • Thumbnail Image
    Item
    Study on Underfill/Solder Adhesion in Flip-Chip Encapsulation
    (Georgia Institute of Technology, 2002-11) Wong, C. P. ; Fan, Lianhua ; Tison, Christopher K.
    Underfill materials are employed in flip-chip assemblies to enhance solder joint reliability performance. The adhesion of underfills with solders is important to the integrity of the flip-chip structure. We have studied the adhesion strength of two underfill samples with tin/lead (Sn/Pb) eutectic solder and tin/copper (Sn/Cu) lead-free solder, benchmarked with a copper surface. It was found that the adhesion of underfills and both solder materials was about 1/3 of the adhesion between underfills and copper. The effect of temperature and humidity aging as well as flux residue on adhesion strength was also investigated. A loss of adhesion was observed after the pressure cooker test, but 85 ℃/85% RH aging and flux residue revealed only a slight influence on adhesion strength. Surface analysis was performed on solid surfaces including copper, Sn/Pb eutectic solder, Sn/Cu lead-free solder and cured underfills by using the three-liquid-probe three-component surface tension method with a goniometer. The surface tension of liquid underfills was measured by the pendent drop method, and their contact angles on copper, Sn/Pb eutectic solder and Sn/Cu lead-free solder were also measured with a goniometer. The thermodynamic work of adhesion for underfills with copper and solder surfaces of different conditions was then calculated following these two surface analysis approaches. It was found that the thermodynamic work of adhesion was not correlated with the lap shear strength of underfills with copper and solder materials. Thus, the wetting property of an underfill on a substrate is not the determining factor for its practical adhesion strength. Various possible techniques for improving the adhesion of underfills and solder materials were then considered, and the use of additives in underfill formulations was experimented. However, we have not observed any significant effect of adhesion strength enhancement from any of these additives. Further tests of these additives with the base underfill formulation seemed to reveal a slight possibility to enhance adhesion of underfills and solders by proper manipulation of the underfill and/or flux formulation.
  • Thumbnail Image
    Item
    Development of Environmental Friendly Non-Anhydride No-Flow Underfills
    (Georgia Institute of Technology, 2002-03) Wong, C. P. ; Zhang, Zhuqing ; Fan, Lianhua
    Most no-flow underfill materials are based on poxy/anhydride chemistry. Due to the sensitizing nature, the use of anhydride is limited and there is a need for a no-flow underfill using nonanhydride curing system. This paper presents the development of novel no-flow underfill materials based on epoxy/phenolic resin system. Epoxy and phenolic resins of different structures are evaluated in terms of their curing behavior, thermo-mechanical properties, viscosity, adhesion toward passivation, moisture absorption and the reliability in flip-chip underfill package. The influence of chemical structure and the crosslinking density of the resin on the material properties is investigated. The assembly with nonanhydride underfill shows high reliability from the thermal shock test. Solder wetting test has confirmed the sufficient fluxing capability of phenolic resins. Results show that epoxy/phenolic system has great potential for an environmental friendly and highly reliable no-flow underfill.
  • Thumbnail Image
    Item
    Development of Reworkable Underfill From Hybrid Composite of Free Radical Polymerization System and Epoxy Resin
    (Georgia Institute of Technology, 2002-03) Wong, C. P. ; Fan, Lianhua
    The application of the underfill encapsulant is to enhance the solder joint fatigue life in the flip chip assembly, typically up to an order of magnitude, as compared to the nonunderfilled devices. Most of the current underfills, however, are primarily thermosetting epoxy resin curing system based materials, which transform into an infusible three dimensional network structure, and exhibit appreciable adhesion and reliability, but lack of desirable reworkability after curing. From the standpoint of polymeric material chemistry, other thermoplastic or thermosetting polymer materials could be of great economic/cost interest as encapsulants for some microelectronic packaging applications. In this paper, the experimental focus was devoted to the study of adhesion, reliability and reworkability of the free radical polymerization (FRP) system, as well as its hybrid composites or blends with phenoxy resin or epoxy resin (EPR), which could be potential underfill materials. The study encompassed formulation screening based on adhesion measurement, and assessment on reliability and reworkability performance for selected compositions developed so far. Compared with common practice of synthesis of a new epoxy resin backbone or specialty polymer, these FRP/EPR hybrid composites from readily available raw materials would represent a cost effective approach toward reworkable underfill with good adhesion and reliability performance.