Person:
Rohatgi, Ajeet

Permanent Link
https://hdl.handle.net/1853/71640
Associated Organization(s)
ORCID
ArchiveSpace Name Record

Filters

2000 - 2004 3
3
3
3
3
Reset filters

Settings
Author: Hanoka, J. I. × Author: Yelundur, Vijay × Start date: 2000 ×

Publication Search Results

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    Beneficial Impact of Low Frequency PECVD SiN(x):H-Induced Hydrogenation in High-Efficiency String Ribbon Silicon Solar Cells
    (Georgia Institute of Technology, 2004-06) Yelundur, Vijay ; Rohatgi, Ajeet ; Hanoka, J. I. ; Reedy, R.
    PECVD SiN(x):H-induced hydrogenation of bulk defects in String Ribbon Si during RTP anneal is investigated in this study to enhance the carrier lifetime and understand the role of the plasma excitation frequency and an in-situ NH3 plasma pretreatment before SiN(x):H deposition. The results show that a low frequency SiN(x):H film with a NH3 plasma pretreatment annealed in RTP at 740°C for 60 seconds enhances the lifetime in String Ribbon Si from 5-6 μs to 90-100 μs. Secondary ion mass spectroscopy underneath SiN(x):H films deposited with deuterated ammonia (ND3) and silane shows greater deuterium incorporation in Si under the low frequency SiN(x):H film. Thus, hydrogen incorporated in Si during SiN(x):H deposition may act as an additional source that enhances hydrogen defect passivation during subsequent RTP treatments. In addition, the effect of the anneal time during RTA for hydrogenation is studied in an effort to reduce the hydrogenation time and improve the retention of hydrogen at defects in Si. The RTA time for hydrogenation is reduced to one second without loss of lifetime enhancement and leads to the fabrication of high-efficiency String Ribbon solar cells (17.9%) with photolithography-defined contacts. A rapid belt furnace contact co-firing scheme is developed based on the short RTA and produces screen-printed 4-cm2 String Ribbon solar cells with efficiencies as high as 15.9%.
  • Thumbnail Image
    Item
    Fundamental Understanding and Implementation of Al-enhanced PECVD SiN(x) Hydrogenation in Silicon Ribbons
    (Georgia Institute of Technology, 2001-06) Rohatgi, Ajeet ; Yelundur, Vijay ; Jeong, Ji-Weon ; Ebong, Abasifreke ; Rosenblum, M. D. ; Hanoka, J. I.
    A low-cost, manufacturable defect gettering and passivation treatment, involving simultaneous anneal of a PECVD SiN(x) film and a screen-printed Al layer, is found to improve the lifetime in Si ribbon materials from 1-10 μs to over 20 μs. Our results indicate that the optimum anneal temperature for SiN(x)-induced hydrogenation is 700°C for EFG and increases to 825°C when Al is present on the back of the sample. This not only improves the degree of hydrogenation, but also forms an effective back surface field. We propose a three-step physical model, based our results, in which defect passivation is governed by the release of hydrogen from the SiN(x) film due to annealing, the generation of vacancies during Al-Si alloying, and the retention of hydrogen at defect sites due to rapid cooling. Controlled rapid cooling was implemented after the hydrogenation anneal to improve the retention of hydrogen at defect sites by incorporating an RTP contact firing scheme. RTP contact firing improved the performance of ribbon solar cells by 1.3-1.5% absolute when compared to slow, belt furnace contact firing. This enhancement was due to improved back surface recombination velocity, fill factor, and bulk lifetime. Enhanced hydrogenation and rapid heating and cooling resulted in screen-printed Si ribbon cell efficiencies approaching 15%.
  • Thumbnail Image
    Item
    PECVD SiN(x) Induced Hydrogen Passivation in String Ribbon Silicon
    (Georgia Institute of Technology, 2000-09) Yelundur, Vijay ; Rohatgi, Ajeet ; Jeong, Ji-Weon ; Gabor, A. M. ; Hanoka, J. I. ; Wallace, R. L.
    To improve the bulk minority carrier lifetime in String Ribbon silicon, SiN(x) induced defect passivation during a post deposition anneal is investigated. Our results indicate that SiN(x) induced hydrogen passivation is very effective when the SiN(x) film is annealed in conjunction with a screen-printed AI layer on the back. In addition, it is found that controlled rapid cooling can be used to enhance the defect passivation process. A model is proposed which relates the high temperature passivation to the release of hydrogen from the SiN(x) film, the injection of vacancies from backside AI alloying, and the retention of hydrogen at defect sites. High efficiency screen-printed String Ribbon solar cells (>14.5%) are fabricated utilizing the simultaneous SiN(x)/AI anneal in a belt furnace for hydrogenation and AI-BSF formation, followed by RTP firing of screen-printed contacts to improve the retention of hydrogen at defects.