Organizational Unit:
Daniel Guggenheim School of Aerospace Engineering
Daniel Guggenheim School of Aerospace Engineering
Permanent Link
Research Organization Registry ID
Description
Previous Names
Parent Organization
Parent Organization
Organizational Unit
Includes Organization(s)
Organizational Unit
Organizational Unit
Organizational Unit
Organizational Unit
Organizational Unit
ArchiveSpace Name Record
Publication Search Results
Now showing
1 - 6 of 6
-
ItemNumerical simulations of real-gas flows with phase-equilibrium thermodynamics(Georgia Institute of Technology, 2020-07-20) Tudisco, PrincipioMotivated by the complex physics of multi-component mixtures in strongly non-ideal, real-gas (RG) conditions reported in the field of chemical engineering, this work aims to address the behavior of multi-phase thermodynamics from a broader point of view. The focus is to evaluate the differences, as well as the possible sources of errors that would arise in a computational fluid-dynamics (CFD) simulation when conventional single-phase and multi-phase equilibrium RG thermodynamics are employed: an area of research that despite the active interest in many communities (especially CFD), has not been completely understood. Knowledge of the effects that multi-phase RG thermodynamics with the assumption of vapor-liquid equilibrium (VLE) can have on a flow dynamics is important because it establishes the relevance of the fully coupled CFD-VLE solver. In fact, this relevance may go beyond the stand-alone calculation of a multi-phase state, providing important insights about the physics that may not be captured if the single-phase assumption is invoked. This work provides an extensive study of RG mixtures from a physical and numerical point of view. The difficulties associated with their modeling are discussed in detail and solutions are provided accordingly. Emphasis is given to the occurrence and suppression of numerical noise in form of pressure oscillations that can pollute the simulation to the point that it cannot be performed. Extension of existing models to eliminate such problem is achieved by incorporating the effects of VLE thermodynamics in a consistent manner, ultimately forming a new and robust tool to investigate the physics further. The resulting model is applied to non-reacting and reacting flows in canonical setups where emphasis is devoted to the discussion of the differences and sources of errors that would occur if this multi-phase behavior is not taken into account. Results show that the different thermodynamic states reached by this advanced model can have an impact on the flow physics, especially in a non-reacting (or more in general cold) regime. In particular, the strong non-linear coupling between the VLE thermodynamics and the transport properties is identified as a key element of difference with respect to the single-phase model counterpart. These differences manifest into the occurrence of localized changes in the fluid properties (such as density) that affect the flow-field in their vicinity, causing visible discrepancies even when time-averaging is performed. Concurrently, results obtained on the reacting side and carried out (for the first time) with finite-rate kinetics suggest that any VLE formation between the products and the reactants may be considered of minor importance. The latter conclusion is supported by the analysis conducted on the multi-phase field which appears to be largely composed of the vapor solution, as expected, hence limiting the analogous effect observed the non-reacting system where a broader range of phase-separation appears instead.
-
ItemSelf-sustained combustion of low grade solid fuels in a stagnation-point reverse-flow combustor(Georgia Institute of Technology, 2013-08-27) Radhakrishnan, ArunThis thesis investigates the use of the Stagnation-Point Reverse-Flow (SPRF) combustor geometry for burning low-grade solid fuels that are attractive for specific industrial applications because of their low cost and on-site availability. These fuels are in general, hard to burn, either because of high moisture and impurity-content, e.g. biomass, or their low-volatiles content, e.g., petroleum-coke. This results in various challenges to the combustor designer, for example reduced flame stability and poor combustion efficiency. Conventional solutions include preheating the incoming flow as well as co-firing with high-grade fuels. The SPRF combustor geometry has been chosen because it was demonstrated to operate stably on standard gaseous and liquid-fuels corresponding to ultra fuel-lean conditions and power densities at atmospheric-pressure around 20-25 MW/m3. Previous studies on the SPRF combustor have proven that the unique, reverse flow-geometry allows entrainment of near-adiabatic products into the incoming reactants, thereby enhancing the reactivity of the mixture. Further, the presence of the stagnation-end created a region of low mean velocities and high levels of unsteadiness and mixing-rates that supported the reaction-zones. In this study, we examine the performance of the SPRF geometry on a specific low grade solid fuel, petroleum coke. There are three main goals of this thesis. The first goal is the design of a SPRF combustor to operate on solid-fuels based on a design-scaling methodology, as well as demonstration of successful operation corresponding to a baseline condition. The second goal involves understanding the mode of operation of the SPRF combustor on solid-fuels based on visualization studies. The third goal of this thesis is developing and using reduced-order models to better understand and predict the ignition and quasi-steady burning behavior of dispersed-phase particles in the SPRF combustor. The SPRF combustor has been demonstrated to operate stably on pure-oxygen and a slurry made from water and petroleum-coke, both at the baseline conditions (125 kW, 18 g/s, ~25 µm particles) and higher power-densities and powder sizes. For an overall combustor length less than a meter, combustion is not complete (global combustion efficiency less than 70%). Luminance imaging results indicate the incoming reactant jet ignites and exhibits intense burning at the mid-combustor region, around 15 jet diameters downstream of the inlet, most likely due to enhanced mixing as a result of the highly unsteady velocity field. This roughly corresponds to the location of the reaction zones in the previous SPRF combustors operating on gas and liquid fuels. Planar laser visualization of the reacting flow-field using particle-scattering reveals that ignition of a significant amount of the reactants occurs only after the incoming jet has broken into reactant packets. Post-ignition, these burning packets burn out slowly as they reverse direction and exit the combustor on either side of the central injector. This is unlike the behavior in liquid and gas-fueled operation where the incoming reactants burned across a highly corrugated, thin-flame front. Based on these findings, as well as the results of previous SPRF studies, an idealized model of combustor operation based on a plug flow reactor has been developed. The predictions suggest that fuel-conversion efficiency is enhanced by the combustor operating pressure and lowered by the heat-losses. Overall, this effort has shown the SPRF geometry is a promising compact-combustor concept for self-sustained operation on low-grade solid-fuels for typical high-pressure applications such as direct steam-generation. Based on these findings, it is recommended that future designs for the specific application previously mentioned have a shorter base-combustor with lower heat-losses and a longer steam-generation section for injection of water.
-
ItemDetermination of flame characteristics in a low swirl burner at gas turbine conditions through reaction zone imaging(Georgia Institute of Technology, 2012-08-27) Periagaram, Karthik BalasubramanianThis thesis explores the effects of operating parameters on the location and shape of lifted flames in a Low Swirl Burner (LSB). In addition, it details the development and analysis of a CH PLIF imaging system for visualizing flames in lean combustion systems. The LSB is studied at atmospheric pressure using LDV and CH PLIF. CH* chemiluminescence is used for high pressure flame imaging. A four-level model of the fluorescing CH system is developed to predict the signal intensity in hydrocarbon flames. Results from imaging an atmospheric pressure laminar flame are used to validate the behavior of the signal intensity as predicted by the model. The results show that the fluorescence signal is greatly reduced at high pressure due to the decreased number of CH molecules and the increased collisional quenching rate. This restricts the use of this technique to increasingly narrow equivalence ratio ranges at high pressures. The limitation is somewhat alleviated by increasing the preheat temperature of the reactant mixture. The signal levels from high hydrogen-content syngas mixtures doped with methane are found to be high enough to make CH PLIF a feasible diagnostic to study such flames. Finally, the model predicts that signal levels are unlikely to be significantly affected by the presence of strain in the flow field, as long as the flames are not close to extinction. The results from the LSB flame investigation reveal that combustor provides reasonably robust flame stabilization at low and moderate values of combustor pressure and reference velocities. However, at very high velocities and pressures, the balance between the reactant velocity and the turbulent flame speed shifts in favor of the former resulting in the flame moving downstream. The extent of this movement is small, but indicates a tendency towards blow off at higher pressures and velocities that may be encountered in real world gas turbine applications. There is an increased tendency of relatively fuel-rich flames to behave like attached flames at high pressure. These results raise interesting questions about turbulent combustion at high pressure as well as provide usable data to gas turbine combustor designers by highlighting potential problems.
-
ItemParticle Vaporization Velocimetry and Quantitative Soot Concentration Measurement in Sooty Flows(Georgia Institute of Technology, 2007-11-15) Yang, PingSoot is a combustion generated pollutant that is both a direct risk to human health and a contributing source to global environmental change. Soot can also be a controlling factor in heat transfer inside combustion systems. Thus there is a growing interest in being able to measure soot and understand its production in practical, turbulent combustion environments. Therefore, the specific objectives of this research work were: (1) developing a way to measure velocity of sooty regions that is compatible with existing methods for measuring temporally and spatially resolved soot concentration fields and (2) using these methods to make quantitative measurements of soot in an unsteady, turbulent-like combustor. The Particle Vaporization Velocimetry (PVV) technique was developed and is compatible with Laser Induced Incandescence (LII), a soot concentration measurement approach. PVV is a flow tagging approach, where a high intensity laser (~2-3 J/cm2) is used to vaporize a small region in the soot field. This approach was demonstrated to produce a long lasting and easily readable flow tag that allows for velocity measurements over a wide range of velocities. LII proved to be the best method for detection the motion of the tag after a fixed delay. PVV and LII were used to measure velocity and two-dimensional soot concentration fields in an acoustically excited burner. In addition, images of soot luminosity were obtained. Both laminar and transitional acetylene diffusion flames were studied. The results reveal that strong acoustic forcing can significantly reduce total flame soot, as well as maximum soot concentrations, while simultaneously increasing the average soot temperature. The influence of acoustically generated vortices on soot formation was studied, and soot and products mixture mostly likely dominant high soot concentration regions. Eventually, these mixtures will be propagated downstream and oxidized as a diffusion flame.
-
ItemFlame stabilization and mixing characteristics in a stagnation point reverse flow combustor(Georgia Institute of Technology, 2007-10-10) Bobba, Mohan KrishnaA novel combustor design, referred to as the Stagnation Point Reverse-Flow (SPRF) combustor, was recently developed that is able to operate stably at very lean fuel-air mixtures and with low NOx emissions even when the fuel and air are not premixed before entering the combustor. The primary objective of this work is to elucidate the underlying physics behind the excellent stability and emissions performance of the SPRF combustor. The approach is to experimentally characterize velocities, species mixing, heat release and flame structure in an atmospheric pressure SPRF combustor with the help of various optical diagnostic techniques: OH PLIF, chemiluminescence imaging, PIV and Spontaneous Raman Scattering. Results indicate that the combustor is primarily stabilized in a region downstream of the injector that is characterized by low average velocities and high turbulence levels; this is also the region where most of the heat release occurs. High turbulence levels in the shear layer lead to increased product entrainment levels, elevating the reaction rates and thereby enhancing the combustor stability. The effect of product entrainment on chemical timescales and the flame structure is illustrated with simple reactor models. Although reactants are found to burn in a highly preheated (1300 K) and turbulent environment due to mixing with hot product gases, the residence times are sufficiently long compared to the ignition timescales such that the reactants do not autoignite. Turbulent flame structure analysis indicates that the flame is primarily in the thin reaction zones regime throughout the combustor, and it tends to become more flamelet like with increasing distance from the injector. Fuel-air mixing measurements in case of non-premixed operation indicate that the fuel is shielded from hot products until it is fully mixed with air, providing nearly premixed performance without the safety issues associated with premixing. The reduction in NOx emissions in the SPRF combustor are primarily due to its ability to stably operate under ultra lean (and nearly premixed) condition within the combustor. Further, to extend the usefulness of this combustor configuration to various applications, combustor geometry scaling rules were developed with the help of simplified coaxial and opposed jet models.
-
ItemQuantitative Acetone PLIF Measurements of Jet Mixing with Synthetic Jet Actuators(Georgia Institute of Technology, 2006-04-11) Ritchie, Brian DouglasFuel-air mixing enhancement in axisymmetric jets using an array of synthetic jet actuators around the perimeter of the flows (primarily parallel to the flow axis) was investigated using planar laser-induced fluorescence of acetone. The synthetic jets are a promising new mixing control and enhancement technology with a wide range of capabilities. An image correction scheme that improved on current ones was applied to the images acquired to generate quantitative mixing measurements. Both a single jet and coaxial jets were tested, including different velocity ratios for the coaxial jets. The actuators run at a high frequency (~1.2 kHz), and were tested with all of them on and in other geometric patterns. In addition, amplitude modulation was imposed at a lower frequency (10-100 Hz). The actuators generated small-scale structures in the outer (and inner, for the coaxial jets) mixing layers. These structures significantly enhanced the mixing in the near field (x/D less than 1) of the jets, which would be useful for correcting an off-design condition in a combustor. The amplitude modulation generated large-scale structures that became apparent farther downstream (x/D greater than 1). The impulse at the start of the duty cycle was responsible for creating the structures. The large structures contained broad regions of uniformly mixed fluid, and also entrained fluid significantly. In addition, highly asymmetric forcing geometries displayed the power of the actuators to control the spatial distribution of jet fluid. This spatial control is important for the correction of hot spots in the pattern factor. In order to extend quantitative acetone PLIF to two-phase flows, the remaining unknown photophysical properties of acetone were identified. Tests showed that the technique could simultaneously capture acetone vapor and acetone droplets. A model of droplet fluorescence was developed, and applied to images acquired in a dilute spray. The sensitivity of the model to the value of the unknowns was evaluated, including a best and worst case. The results revealed that several liquid acetone photophysical properties must be measured for the further development of the technique, especially the phosphorescence yield. Quantitative two-phase acetone PLIF will provide a powerful new tool for studying spray flows.