Modelling of multistage axial-centrifugal compressor configuration using the streamtube approach

dc.contributor.advisor Prasad, Jonnalagadda V. R.
dc.contributor.advisor Neumeier, Yedidia
dc.contributor.author Mishra, Abhishek
dc.contributor.committeeMember Sankar, Lakshmi N.
dc.contributor.committeeMember Jagoda, Jechiel I.
dc.contributor.committeeMember Srivastava, Rakesh
dc.contributor.department Aerospace Engineering
dc.date.accessioned 2019-08-21T13:47:30Z
dc.date.available 2019-08-21T13:47:30Z
dc.date.created 2019-08
dc.date.issued 2019-05-21
dc.date.submitted August 2019
dc.date.updated 2019-08-21T13:47:30Z
dc.description.abstract Quasi-1D flow models based upon mean-line analysis are quite popular for design and performance evaluation of multistage axial and centrifugal compressors. However, they are not so readily used for analyzing the dynamic behavior of the compressor. In this work, an unsteady 1D axial-centrifugal compressor model is developed, whereby the stage elements, i.e., rotors and stators are modelled as diffusing streamtube elements. The analysis, being independent of any stage aerodynamic force and work terms, accurately predicts the performance of axial and axial-centrifugal compressors by the incorporation of various loss mechanisms compounding to stagnation pressure losses within stage elements. The off-design performance, especially close to the surge and choke line, is captured using novel models, particularly developed for incidence/sudden turning and mixing losses. These inlet turning and mixing loss models constitute an important feature of this work and are implemented by the inclusion of a single model parameter. This parameter called mixing loss factor, is then tuned for nominal shaft speed and is subsequently used to predict the compressor performance for different speeds ranging from 50% to 105%. The surge line is also accurately predicted by correlating the slope change criteria of constant speed characteristic curve to the instability onset point, which aligns well with the suitable choice of critical/stall incidence angle for the stage elements. Furthermore, the tuned model is used to predict the performance of the axial-centrifugal compressor at the aforementioned range of speeds. The diffuser loss, diffuser incidence angle and throat Mach number are calculated for the well-known UTRC-High Efficiency Centrifugal Compressor (HECC) and the results are validated with data from the literature. The dynamic communication between two connected streamtubes is established using a novel boundary element called Compact Interface Element (CIE), which is developed by making use of the characteristics-based approach. The CIE achieves reference frame transformation between the successive diffuser elements and also incorporates complex loss mechanisms due to sudden flow turning, mixing, shocks etc. Within the streamtube, 1D time-dependent conservation equations are solved using the second-order accurate Kurganov-Tadmor scheme, while at the boundary between the streamtubes, the dynamic compact element updates the interface conditions in time. Another aspect of compressor operation is the observance of aerodynamic instabilities as the compressor is throttled towards stall. Several simulations indicate onset of instabilities close to the peak of compressor characteristic when a large plenum is present at the compressor end. Without any end plenum or low speed operation, it is found that few stable points exist on the positively-sloped portion of the characteristic curve. Importantly, Greitzer's B-parameter provides a good qualitative validation of the instability onset point. Further throttle closure, however, leads to oscillations, where the low frequency mode represents the fundamental axial mode of the compressor. It is shown that the instability modes obey a general Rayleigh's criterion, where they are affected by the phase between pressure fluctuations and shaft power addition oscillations. The model finds applications in compressor design and analysis where the simulation results together with the test data using pressure signatures, provide the identification of stalling and choking stages.
dc.description.degree Ph.D.
dc.format.mimetype application/pdf
dc.identifier.uri http://hdl.handle.net/1853/61597
dc.language.iso en_US
dc.publisher Georgia Institute of Technology
dc.subject Reduced-order modelling
dc.subject Streamtube analysis
dc.subject Quasi-1D model
dc.subject Compressor instabilities
dc.subject Dynamic compact interface
dc.subject Loss mechanisms
dc.title Modelling of multistage axial-centrifugal compressor configuration using the streamtube approach
dc.type Text
dc.type.genre Dissertation
dspace.entity.type Publication
local.contributor.advisor Prasad, Jonnalagadda V. R.
local.contributor.corporatename College of Engineering
local.contributor.corporatename Daniel Guggenheim School of Aerospace Engineering
relation.isAdvisorOfPublication 933b7ff4-7a2e-4eab-9618-bc6303890af3
relation.isOrgUnitOfPublication 7c022d60-21d5-497c-b552-95e489a06569
relation.isOrgUnitOfPublication a348b767-ea7e-4789-af1f-1f1d5925fb65
thesis.degree.level Doctoral
Original bundle
Now showing 1 - 1 of 1
Thumbnail Image
7.25 MB
Adobe Portable Document Format
License bundle
Now showing 1 - 1 of 1
No Thumbnail Available
3.87 KB
Plain Text